 | Bulkhead Braces (Front & Rear)
$18.00 |
| CNC Machined from billet 6061 aluminumStock replacementCustom look |
| | Lower Suspension Arm
$29.00 |
| These arms were designed for those who like to race.With their adjustability to lower your truck farther than any other arm without sacrificing shock travel, these arms are great for those who race.Not only are they for the racer but the basher can take full use of its features also.Includes an exclusive pin brace to nearly eliminate front lower pin from bendingWorks best in conjunction with FLM s... |
 | Upper Suspension Arm (pair)
$29.00 |
| Made in the USAMade from the finest 6061 T6 Aluminum.These A-Arm sets are very durable and easy to install.These arms are sold in Pairs.2 are needed to complete the truck. |
 | Hinge Pin Kit (steel)
$12.00 |
| Made in the USAMachined from high strength steelStock bulk upgrade |
| FLM Bulk Hinge Pin Kit (steel)
$12.00 |
| Machined from high strength steelStock bulk upgrade |
 | Front Skid Plate
$14.00 |
|
CNC Machined from billet 6061 aluminum
Lightweight design
|
 | Rear Skid Plate
$12.00 |
|
Made in the USA
CNC Machined from billet 6061 aluminum
Lightweight design
|
 | Chassis Braces
$30.00 |
|
CNC Machined from billet 6061 aluminum
These fit older versions of the T and E-maxx
Direct replacement
|
 | Transmission Skid Plate
$7.50 |
| CNC Machined from billet 6061 aluminumFits older T and E-maxxs with stock or FLM chassis bracesAlso work on FLM Chassis kits (T and E-maxx) |
| | Throttle Servo Mount
$12.00 |
|
CNC Machined from billet 6061 aluminum
Stock replacement
Fits all T-Maxx models
|
| | Motor Mount
$18.00 |
|
CNC Machined from billet 6061 aluminum
Direct replacement for all T-maxx models
|
| | T-Maxx Lightweight Chassis
$75.00 |
| Designed for severe duty. Chassis is machined out of billet 6061 aluminum for durability and strength. 6mm thick. Predrilled for Fast Lane's 3 point chassis brace. Threaded mount for steering servo. Pockets milled for bulkheads, so the center of gravity is not raised. Includes all necessary hardware with standoffs to mount the reverse servo. Fast Lane's extreme abuse warranty. Replacement cost per... |
| | Front Driveshaft Kit
$21.00 |
|
CNC Machined from high strength steel
Extreme duty drive cups
Includes front drive cup and brake cup for 3.3 style brakes
|
 | Front Bulkeads
$38.00 |
| Made in the USACNC Machined from the finest 6061 T6 Aluminum.These Bulkheads are as strong as they are great looking!Lightweight designFits all Maxx modelsIncludes lower arm pin |
 | Front Combo Bulks
$60.00 |
|
Made in the USA
CNC Machined from billet 6061 aluminum
Increases strength to entire bulkhead section
This bulk accepts the older Maxxs, Traxxas part# 4981 diff gear
Diff case and bulk are machined into one unit
Includes lower arm pin
|
| Front Hybrid Bulk
$75.00 |
|
Made in the USA
CNC Machined from billet 6061 aluminum
Increases strength to entire bulkhead section
This bulk accepts 1/8 scale style diffs (ring gear must be less the 1.500 inches)
Diff case and bulk are machined into one unit
Includes lower arm pin
|
 | Rear Bulkead set
$38.00 |
| Made in the USAMade from the finest 6061 T6 Aluminum.These Bulkheads are as strong as they are great looking!Lightweight designIncludes lower arm pin |
 | Rear Combo Bulk
$60.00 |
|
Made in the USA
CNC Machined from billet 6061 aluminum
Increases strength to entire bulkhead section
This bulk accepts the older Maxxs, Traxxas part# 4981 diff gear
Diff case and bulk are machined into one unit
|
| Rear Hybrid Bulks
$75.00 |
|
Made in the USA
CNC Machined from billet 6061 aluminum
Increases strength to entire bulkhead section
This bulk accepts 1/8 scale style diffs (ring gear must be less the 1.500 inches)
Diff case and bulk are machined into one unit
Includes lower arm pin
|
 | Adjustable Shock Tower
$24.00 |
| 20 adjustable positions from racing to bashing!CNC Machined from billet 6061 aluminum3/8 thick for extreme abuseAdjusts an additional .500 than previous designTowers has been machined to accept GS Storm and Hot Bodies Lightning wing mountThese shock towers were designed for those who want the most out of there Maxx. |
 | LST2 shock conversion
$12.00 |
| Made in the USAMachined from billet 6061 aluminumUse LST2 shocksRecquires mod to stock towerDirect fit for FLM towers |
 | 3905 Diff Cup with Modified Traxxas Gear
$32.00 |
|
Machined from billet 7075 aluminum diff cup
Screw size is increased to 3mm for durability
Direct replacement
Includes aluminum drive cup and modified stock gear
|
